| |
G8MNY > TECHNI 17.04.12 07:24l 76 Lines 3436 Bytes #999 (0) @ WW
BID : 32419_GB7CIP
Read: GUEST
Subj: PALSTAR PS06 6A PSU
Path: IZ3LSV<IK2XDE<DB0RES<PI8CDR<GB7YEW<GB7CIP
Sent: 120416/2232Z @:GB7CIP.#32.GBR.EU #:32419 [Caterham Surrey GBR] $:32419_GB
From: G8MNY@GB7CIP.#32.GBR.EU
To : TECH@WW
By G8MNY (New Jan 07)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
This is a simple design, used on this commercial PSU. It has no overvoltage or
fuse protection other than a 1A slow blow mains fuse. It does include current
limit & output foldback.
HOW IT WORKS
The bridge rectifier charges up C1 & C2 to 23V. R1 & R2 via hum decoupling C3,
puts current into Tab transistor Q3. This drives the two outputs Q6 & Q7.
The output going high powers the zener diode D2 & LED via R5. When the voltage
sample via R6, R8 & VR2 is 0.5V higher than the zener voltage Q1 turns on
removing the drive to Q3. (note a broken lead to the LED means +23V output!)
When too much current flows, Q2 will turn on as the voltage across R13 & R14
exceeds the voltage set up across R4 by current from VR1. Q2 turning on via D1
remove the drive to Q3. When the output voltage falls below the zener reference
output foldback occurs, to maintain a safe output current of about 1 amps into
a short circuit load.
ÚÄÄÄÄÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÂÄÄÄÄÄ¿
/ \ ³ ³ R1 ³/ ³ ³
AC_/'BR1`\_AC ³ ³ ÃÄR2ÄÂÄÄÄÂÄÄ´Q3 ³ ³Insulated
A~ \ / ~B ³ ³ ³ ³ ³ ³\e ³/ ³/ on Heatsink
On `\ /' ³ +³ ³ ³ _³_ ÃÄÄÄÄÅÄÄÄÄÄ´ Q7
Heat- ³ ³+ === ³ ³ \_/ ³ Q6³\e ³\e
sink ³ === ³C2 ³ ³ D1³ R4 R13 R14
³ C1 ³ ³ ³ ³ \³ ³ ÃÄÄÄÄÄÁÄÄÄÄÄÄÄÂÄÄÂÄÄÂÄ>+ 13.8V
³ ³ ³ ³ ³ Q2 ÃÄÄ´ ³ I rd E ³ ³ ³
³ ³ ³ ³ ³ e/³ ³ ³ ³ ³ ³
³ ³ ³ ³ ³ ÀÄÄÄÄ)ÄÄÂÄÄÄ´ ³ ³ ³
³ ³ ³ ³ ³ ³ ³ ³ ³ ³ ³
³ ³ ³ ³ ÃÄÄÄÄ¿C4 ³ R5 R6 ³ ³ ³
³ ³ ³ ³ \³ === ³ ³ ³ ³ ³ ³ Car
³ ³ ³ ³ Q1 ÃÄÄÁÄÄÄ)ÄÄ)ÄÄÄ´ ³ ³ (0) Point
³ ³ ³ C3³+ e/³ ³ ³ ³ ³ ³ À¿
³ ³ ³ === ÃÄÄÄÄÄÄÄÄ)ÄÄÙ ³ ³ ³ ³
³ ³ ³ ³ _³_ ³ ³ ³C5³ ³ @ 6A
³ ³ ³ ³ D2/_\ R7 R4 ³ === ³
³ ³ ³ ³ N³rd ³ ³ C6 ³+ ³ ³
³ ³ ³ ³ _³_ ³ ³ === ³ ³
³ ³ ³ ³LED\_/ð VR1 VR2 ³ ³ ³
³ ³ ³ ³ D³bk ³ ³ J bk F ³ ³ ³
ÀÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÁÄÄÁÄ>0V
M A I N P C B TERMINAL PCB
No R C Q D VR BR
1 680 3m3 25V 2SC1815 1N4148 10k 10A
2 1k 2m2 25V 2SC1815 6.1V 2k
3 --- 100u 35V 2SD440
4 470 10n
5 1k5 220u 25V ------
6 330 10n
7 Link
8 2k7
13 0.51
14 0.51
MODIFICATIONS
I have modified mine..
1/ Added more smoothing off PCB, 10,000uF 25V across C1.
2/ Changed C5 for a 1000uF 16V.
3/ Added a 1N4005 diode across output to protect against reverse voltage.
4/ Added a 1N4005 diode from output to input to protect against +load voltages.
5/ Changed very HOT R13 & R14 for 0.22 2.5W & readjusted VR1 for 6A max.
Note as R7 is a 0 ohms link, so do not take VR1 to Zero ohms!
Why Don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
