OpenBCM V1.08-5-g2f4a (Linux)

Packet Radio Mailbox

IZ3LSV

[San Dona' di P. JN]

 Login: GUEST





  
G8MNY  > TECH     26.10.13 09:22l 78 Lines 3104 Bytes #999 (0) @ WW
BID : 42097_GB7CIP
Read: GUEST
Subj: Band 2 6el Broadband Yagi
Path: IZ3LSV<I0OJJ<GB7CIP
Sent: 131026/0708Z @:GB7CIP.#32.GBR.EU #:42097 [Caterham Surrey GBR] $:42097_GB
From: G8MNY@GB7CIP.#32.GBR.EU
To  : TECH@WW

By G8MNY                                (New Sep 11)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
On looking at an large old well made home-made 6el broadcast Yagi beam (scrap)
as a starting point, I decided to re-model it using the MMANA-GAL program
(CD in 2010 RSGB yearbook & online). It showed it to be rubbish as it was!

Unlike simple narrow band aerial designs, I wanted this design to be broadband
enough for 87.5-108MHz, with good front to back ratio & have some useful gain.
Using the optimisation over frequencies near the edge of the band, I ended up
with this quite acceptable compromise in 20mm ally tube for the elements, &
boom was 40mm & 2.54m long!

 2x
849     4x
 ³cm    732
 ³       Ú¿cm  2x
 ³       ³³   647            2x
 ³       ³³   ³cm            614        2x
 ³       ³³   ³               ³cm       583             2x
 ³       ³³   ³               ³          ³cm            522
 ³       ³³   ³               ³          ³               ³cm
 ³       ³³   ³               ³          ³               ³
 ³       ³³   ³               ³          ³               ³
 ³       ³³   ³               ³          ³               ³
 ÃÄÄÄÄÄÄÄÅ0ÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´
 ³  326  ³³186³      713      ³    550   ³       758     ³
 ³   cm  ³³cm ³       cm      ³     cm   ³        cm     ³
 ³       ³³   ³               ³          ³               ³
 ³       ³³   ³               ³          ³               ³
 ³       ³³   ³               ³          ³
 ³       ³³   ³               ³
 ³       ³³   ³
 ³       ³³
 ³       ÀÙ
 ³    98mm dia
     folded ends.
  
Freq  Gain  F/B   R   J                        
 88   7.9  14.5   97  -4                    _-~~~-_
 90   7.7  12.8  146  41                   /       \
 92   7.6  11.7  198  71          Typical Þ         Ý
 94   7.7  11.1  252  86           polar   \       /
 96   7.8  11.0  308  82           diagram  \_   _/
 98   8.0  11.0  355  52           across     >ú<
100   8.3  11.3  375  -2           whole     (   )
102   8.6  11.7  346 -64           band.      -.-
104   9.0  12.4  263 -89
106   9.6  13.6  165 -49 
108  10.1  15.6   87  47

AERIAL Z
This table shows the impedance of this folded dipole feed point is approx. 300
Ohms balanced over most of the band. This is not normal as a folded dipole
increases the impedance by 4 & the reflector & director usually reduces it by
4, resulting the usual 75ê. But this design is optimised for bandwidth, so 
we to do extra matching, to get 75ohm. I used a small centre tapped VHF 2 hole
ferrite bread as the balun, with 2x 2 turns on it all in the connection box.

 .========================.
((Folded          Dipole  ))
 '========()   ()=========='
           \__/³
       bead(oo)³_____________________ 
           ctÀ(À)_____75ê Coax______ 

Z MEASUREMENTS
Using an MFJ analyser, the match to 75ê is pretty good over most of the band as
predicted by the model. I hope when I put it up on a rotator it works as
predicted too.


Why don't U send out an interesting bul?

73 De John, G8MNY @ GB7CIP


Read previous mail | Read next mail


 05.11.2024 07:52:27lGo back Go up