|
G8MNY > TECH 15.06.08 00:50l 113 Lines 4604 Bytes #999 (0) @ WW
BID : 59058_GB7CIP
Read: GUEST
Subj: Marconi Distortion Meter TF2337
Path: IZ3LSV<IK2XDE<DB0RES<ON0AR<GB7CIP
Sent: 080614/2238Z @:GB7CIP.#32.GBR.EU #:59058 [Caterham] $:59058_GB7CIP
From: G8MNY@GB7CIP.#32.GBR.EU
To : TECH@WW
(8 Bit ASCII Graphics use code page 437 or 850)
Hi thanks for reading this.
I have just been working on one of these old AF automatic distortion meters. It
is quite different to the usual fiddly variable Wien Bridge deep notch type. So
it is ideally suited for setting up tape machines, where the playback level &
frequency will never be that steady.
Level Meter Distortion Meter
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³--ÚÄÄÄÄÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄÄÄÄÄ¿--³
³ ³ú ³³ú ³ ³
³ ³ '. ³³ '. ³ ³
³--ÀÄÄÄÄÄÄÄÄÄÄÄÙÀÄÄÄÄÄÄÄÄÄÄÄÙ--³
³ ³
³ 0 ³
³ Function Distort ³
³ [][][][] [][][][] ³
³ O o ³
³ [][][][][][][][] ³
³ O í ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
In Level Range Mains
Level Ranges:- 30V, 10V, 3V, 1V, 300mV, 100mV, 30mV, 10mV.
:- 30, 20, 10, 0, -10, -20, -30, -40 dBV
Responce :- 10Hz - 250kHz @ -3dB
Distortion Filters 400Hz, 1kHz & External.
Distortion Ranges: 30%, 10%, 3%, 1% min to 0.2%
& dBs -10 -20 -40 -40 min to -55dB
Harmonic Responce: 1.5x Filter to 130kHz @ -3dB
Mains 230V. odd 3 pin 1cm square socket.
The automatic refers to the distortion measurement does not need the zero level
reference level to be set first. (But is must be reading 30-100% on the level
meter scale.) This is done not by a very low distortion AGC system as you might
think, but a cleaver meter movement with 2 coils & no return springs. One coil
is fed with rectified DC from the input level detector 1 & acts as the return
spring & the other is fed from an 2nd detector from a high pass filter that
removes all of the fundamental, so it just the harmonics. The resultant meter
deflection is the distortion fraction.
In ÚÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ACÚÄÄÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄÄÄ¿
oÄÄ´LevelÃÄ´InputÃÄÂÄÄÄÄ´LevelÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´LEVEL METERÃÄÄÄÄÄ¿
³Atten³ ³ Amp ³ ³ ³Det 1³ DC ÀÄÄÄÄÄÄÄÄÄÄÄÙ ³
ÀÄÄÄÄÄÙ ÀÄÄÄÄÄÙ ³ ³ ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³
³ ÀÄÄÄÄÄÙ ÚÄÄÄÄÁÄÁÄÄÄÄÄ¿
³ ÚÄÄÄÄÄÄÄÄÄ¿ ³ DISTORTION ³
³ oÄ´400Hz HPFÃÄo ÚÄÄÄÄÄ¿ ÚÄÄÄÄÄ¿ ³2 COIL METER³
³ ÃÄÄÄÄÄÄÄÄÄ´ ³ Set ³ ³Level³ ÀÄÄÄÄÂÄÂÄÄÄÄÄÙ
À>oÄ´ 1kHz HPFÃÄo<Ä´Gain ÃÄÄ´Det 2ÃÄÄÄÄÄÄÄÙ ³
ÀÄÄÄÄÄÄÄÄÄÙ ³ Amp ³ ³ ÃÄÄÄÄÄÄÄÄÄÙ
oÄ External ÄÄo ÀÂÂÂÂÂÙ ÀÄÄÄÄÄÙ DC
^ÄÄÙDist Range
It just uses simple RC transistor Amps & bridge diodes for the electronics. The
notches are sealed LC high Q units. (M derived?)
There are only 3 presets:- Level gain, Distortion gain, & input amp Bias.
DISTORTION MEASURING PRINCIPLES
f1 f2
³ f1 0dBÄ´ | ÚÁÄÄÄÄÄÄ ³ f1
Level³ ³ f2 ³ | ³ High ³ f2
³ ³ ³ f3 ³ | ³ Pass ³ ³ f3
³ ³ ³ ³ f4 f5 -60dB_³___|_/ Filter ³ ³ ³ f4 f5
ÀÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÁ ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄ ÀÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÁÄÄÄÁ
Distorted Signal Filter Filtered Signal
The high pass filter must completely remove the fundamental & ale LF hums etc.
but leave all the harmonics intact. The detectors (especially the distortion
one) should be a true RMS type, as the waveform will generally be very complex
& nothing like a sine wave. The ratio of f1 to all the harmonics f2+++ is the
distortion factor.
Calibration is done by adding in a 2nd tone (e.g. 3-10x freq) via high value Rs
at say 10% of the level to indicate 10% distortion. The distortion meter
bandwidth can also be checked with this circuit.
1V 1kHz Äo-oÄÄÄ10kÄÄÂÄÄÄÂÄÄÄÄÄÄ¿
Osc 1 o ³ ³ ³
_³_ ³ ³ Distortion
³ DVM Meter
100mV ³ _³_ _³_
2-20kHz Äo-oÄÄÄ10kÄÄÙ
Osc 2 o
_³_
To check the HPF filter is working OK a very pure sine wave is needed, so an LC
tuned circuit after a sig gen is used. But I did find that > 0.5V @ resonance
on the meter did make the inductor distortion rise > 0.01% !
Osc 88mH 500mV
50mV 1kHz ÄÄÄ((((()ÄÄÂÄÄÄÄÄ¿ Hi Z
low Z ³ Distortion
³ 0.28uF === Meter
_³________________³_____³
See my bul "Simple 1kHz AF osc".
Why don't U send an interesting bul?
73 de John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |