| |
G8MNY > TECH 02.04.08 23:00l 121 Lines 5235 Bytes #999 (0) @ WW
BID : 51939_GB7CIP
Read: GUEST
Subj: 88mH Coils, Explained!
Path: IZ3LSV<IW2OHX<IQ0LT<IK2XDE<DB0RES<ON0AR<GB7CIP
Sent: 080402/0028Z @:GB7CIP.#32.GBR.EU #:51939 [Caterham] $:51939_GB7CIP
From: G8MNY@GB7CIP.#32.GBR.EU
To : TECH@WW
By G8MNY (Update Dec 07)
(8 Bit ASCII Graphics use code page 437 or 850)
After seeing several buls on 88mH coils, I thought I would explain what they
were used for by the millions in the UK telecomms industry.
LINE THEORY
The basic 600ê 2 wire telephone line system is quite lossy. This is due to too
high a capacity between the wires & the copper resistance, this causes high
loss & also higher loss at higher frequency than ideal.
Simple Line A Loaded Line section
ÄÄÄÂÄÄRÄÄÂÄÄRÄÄÂÄÄRÄÄÂÄÄÄ ÄÄÄÂÄÄ((()ÄRÄÄÂÄÄÄ
600ê === === === === 600ê 1200ê === :::: === 1200ê
ÄÄÄÁÄÄRÄÄÁÄÄRÄÄÁÄÄRÄÄÁÄÄÄ ÄÄÄÁÄÄ((()ÄRÄÄÁÄÄÄ
The capacitance & resistance value of the wires can't be changed. Reducing the
load Z flattens the frequency response, but increases the loss (a useful trick
for short music circuits!). But adding series inductance spaced evenly along
the line to make the line look like a cut off filter has several effects...
1/ increases the line impedance (matching transforemers need for 600ê!)
2/ substantially reduces the line loss below the cut off frequency
3/ & flattens the comms band frequency response.
Normal 600ê Loaded 1200ê
Line Loss (e.g. 20 miles) Line Loss
dB dB
30´ / 30´ Þ
³ / ³ Ý
20´ ./ 20´ Flatter response Ý
³ __..-~ ³ And Half the Loss Þ
10´------ÄÄÄÄ~~~ 10´ __/
³ ³ -------ÄÄÄÄÄ~~~
0ÅÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂ>Hz 0ÅÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂÄÄÄÂ>Hz
100 200 500 1k 2k 5k 10k 100 200 500 1k 2k 5k 10k
The standard for cables between telephone exchanges (office) was to use a
loaded cable with an 88mH balanced coil every 2000 yards, starting 1000 yards
from the exchange & completing the last 1000 yard pi section with a capacitor
or a 44mH terminated inductor half section.
1000 Yards 2000 Yards 1000 Yards
ÄÄÄÂÄÄÄÄÄÄ((()ÄÄÄÄÄÄÄÂÄÄÄÄÄÄ((()ÄÄÄÄÄÂÄÄÄÄ ÄÄÄÂÄÄÄÄÄÄ((()Ä
1200ê === :::: === :::: === OR === :::: 1200ê
ÄÄÄÁÄÄÄÄÄÄ((()ÄÄÄÄÄÄÄÁÄÄÄÄÄÄ((()ÄÄÄÄÄÁÄÄÄÄ ÄÄÄÁÄÄÄÄÄÄ((()Ä
88mH 88mH (Made up to) 44mH
(1 section)
<- - full section - -> <- half section ->
BACK TO THE COILS
The coils consist of 2 identical bifilar wound windings on a common ferrite
core, they are quite high Q, & capable of keeping their inductance with up to
50mA of DC current flowing (which is a lot for a pot core!) which is why they
are quite large for the max of 10mW of AF signals on telecomms lines.
Wire colours are normally Black & White Red/Black & Red/White, & it should be
quite easy to identify the 2 line pairs.
_..._
Pot Core <_ _>===== 2 pairs
2cm tall ³ ~~~ ³===== of wires
2.5cm dia ³ ³
\_ _/
~~~
Some coils are ally can encapsulated, others plastic & some not at all.
INDUCTANCE VALUE
Watch out for the 44mH ones, as they look much the same other than labelling &
have half the 88mH test inductance values below.
Centre Centre
______ Tap Tap ÚÄÄÄÄÄÄÄÄ¿
)::( o )::(o\ / L Cancelles
)::( WRONG )::( X so just a
o )::(___ o )::(_/ \___ few mH
³_______88mH ³___________ ?
If just 1 winding is used then you have 22mH. By paralleling the 2nd coil you
get half the DC resistance, but the phase must be right!
_____ ÚÄÄÄÄÂÄÄ ÚÄÄÄÄÄÄÄÄÂÄÄ
)::( o )::( o o )::(o\ / L Cancelles
)::( 22mH OR )::( 22mH WRONG )::( X so just the
)::(_____ )::( )::(_/ \ odd mH
ÀÄÄÄÄÁÄ ÀÄÄÄÄÄÄÄÄÁÄÄ
USES
So with suitable capacitors they make useful AF filters etc.
They can be used as isolation transformers, not too well isolated, & no good
for LF response with low L value.
One can also be used as an efficient voltage step up or a -rail inverter with
just 2 transistors in flip flop. Note the push pull gives nearly 100% output
all the time so smoothing is not needed in some applications!
+12V ÄÂÄÄÄÂÄÄÄÄÂÄÄÄÂÄÄÄÄ¿
55mA ³ e\³ 2k2 2k2 ³/e
³+ ÃÄÄ´ ÃÄÄ´ 2x 50V PNP
100u === /³ 22k 22k ³\ 100mA
³ ³ \ / ³
³ ³ X ³
³ ³_____/ \_____³
³ ³ ³
³ ³ ========= ÃÄÄ´<ÃÄÂÄÄÂÄÄ> -11V 50mA
³ ÃÄ(((()Â(((()ÄÙ ³ ³ - (unregulated)
³ ÀÄÄÄÄÄÄ)ÄÄÄÄÄÄÄÄÄ´<ÃÄÙ ===100u
0V ÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄ>
See my buls on "Passive CW Headphone Filter", "AF 2 Tone Test Osc Design" &
also "DC Power Conversions".
Why Don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
