| |
G8MNY > TECH 19.06.24 10:29l 74 Lines 3060 Bytes #999 (0) @ WW
BID : 9928_GB7CIP
Read: GUEST
Subj: Drake TC-3300-LP QRO LP Filter
Path: IZ3LSV<DB0ERF<OK0NAG<OK0NBR<SR1BSZ<EA2RCF<I0OJJ<GB7CIP
Sent: 240619/0907Z @:GB7CIP.#32.GBR.EURO #:9928 [Caterham Surrey GBR] $:9928_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Update Oct 19)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
I have reverse engineered this very high performance QRO HF Tx low pass filter.
It was used with a QRO PA & it is nice to know, that no matter what QRM you may
cause other HF users, above HF all is quieter than can be measured!
It has other uses, where say 3el HF tri-bander with 400W is below a 6M 5el beam
feeding a band filtered Rig enabling reduced QRM between both bands.
The specification is 1kW MAX @ HF, Attenuation > 80dB above 41MHz
Through loss is practically un-measurable (< 0.05dB?) DC-30MHz
0dB_³__________________
-3dB´ ~\
-10dB´ Ý
-20dB´ |
-30dB´ Þ
-40dB´ Ý
-50dB´ |
-60dB´ Þ
-70dB´ |
-80dB´ V~Ä-._
ÅÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂ Freq
0 5 10 15 20 25 30 35 40 45 50 MHz
THE CIRCUIT
This is a type of M derived Low Pass filter with 3 suck-out trap sections, as
well as « + 1 + « Pi low pass sections, that act more like 4 Pi sections!
L2 L3 L5 L6 Coils are silver plated 3mm í wire
o)ÄÂÄ(((()ÄÂÄ(((()ÄÂÄ(((()ÄÂÄ(((((ÄÂÄ(o L1 = L7 = 0.3uH, 8.5 T on 9mm former
³ ( === ( === ( ³ L2 = L6 = 0.4uH, 7 T on 15mm former
³ ( L1 ³C2 ( L4 ³C4 L7 ( ³ L4 = 0.13uH, 3.5 T on 9mm former
³=== C1 ³ === C3 ³ C5 ===³ L3/5 = 0.4uH each, wound as centre
ÀÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÙ tapped of 15T on 15mm former
C1 = C5 = 53pF bolted through Mica washer disk
C2 = C4 = 186pF bolted through double sided Mica washer disks
C3 = 124pF larger bolted through Mica washer disk
The 3 shunt traps L1/C1, L4/C3, & L7/C5 all resonate at 40MHz
PHYSICAL CONSTRUCTION
- - - - - - - - - BOTTOM COVER REMOVED- - - - - - - - -
³ ³ ³ ³
SO239³ L2 ³ L3 L5 ³ L6 ³SO239
ÚÄÄ´ /~|||||| º³º /~||||||| ||||||| º³º ||||||~\ ÃÄÄ¿
³ ³] |||||| [º³º] ||||||| ||||||| [º³º] |||||| [³ ³
ÀÄÄ´ \ |||||_/ º³º ||||||||||||||_/ º³º \_||||| / ÃÄÄÙ
³ ððð ³C2 __/ C4³ ððð ³
³ ððð L1 ³ L4 ððð ³ L7 ððð ³
³ ___\n___C1 ³ _____\n_____C3 ³ C5___n/___ ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
TOP CHASSIS
The SO239s are riveted on, as are the 2 divider plates. The top chassis has
folded edges tapped for screws etc. not shown here for simplicity. The bottom U
channel shaped cover is screwed on into the folded edges & it has RF fingering
to help ground the 2 central dividers. The cover is the bottom base mounting.
(e.g. above is upside down in use.)
See my tech bul "6m VHF Filter Design" & "Analyser Takeda Riken TR4122B".
Why Don't U send an interesting bul?
73 de John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
