| |
G8MNY > TECH 17.06.24 08:01l 89 Lines 3785 Bytes #999 (0) @ WW
BID : 9754_GB7CIP
Read: GUEST
Subj: 144/432MHz Homebrew Diplexers
Path: IZ3LSV<DB0ERF<DK0WUE<PD0LPM<I0OJJ<GB7CIP
Sent: 240617/0646Z @:GB7CIP.#32.GBR.EURO #:9754 [Caterham Surrey GBR] $:9754_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Correction Jun 04)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
CIRCUIT/LAYOUT
ÚÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄ¿
³ 1T () 1T () ³
³ ³ ³ ³
432 coax OÄÄÄÄ´ÃÄÄÁÄÄ´ÃÄÄÄÁÄÄ´ÃÄÄÄ¿ ³
³ 15pF 5.5pF 15pF \ ÃÄÄ SO
ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ *ÄÄÄÄ 239
³ 3T 4T 3T / ÃÄÄ
144 coax OÄÄ()))ÄÂÄ())))ÄÂÄ()))ÄÄÄÙ ³
³ ³ ³ ³
³ 18pF=== === 18pF ³
ÀÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÙ
DESCRIPTION
It consists of 2 paths of low & high pass filters, each path built on a wall of
a double sided PCB BOX on opposite sides.
The UHF pass filter consists of 15pF 1 Turn to ground 5.5pF (2.2//3.3) &
another 1 turn to ground, & finally a 15pF to the aerial socket at the end of
the box. The coils are about 5mm diameter in 0.5mm dia Wire (22SWG).
The VHF pass filter consists of 3 Turns with 18pF to ground, then 4 turns &
another 18 pF to ground, & finally a 3 Turns to the aerial socket.
The box is 1" square soldered to the socket, & about 3-4" long. The component
connections are soldered to knifed up 6mm square pads. The exact coil sizes
needed are dependent on the real Cap values & box layout. So adjust the coil
shapes (& size if needed) in the RF path for best SWR on each band.
The centre separator is soldered in after all SWR coil adjustments are made.
Then retested, then a lid is soldered.
-----------------------------------------------------------------------------
Here is another design for a VHF/UHF Diplexer, this came originally from VKNET
I don't know the bands, it is assumed from the inductors that the VHF is 2m &
the UHF 70cms.
VHF UHF DIPLEXER
ANTENNA
o
L1 L2 L3 ³ C4 C5 C6
VHF oÄÄÄÄÂÄÄ0000ÄÄÂÄÄ0000ÄÄÂÄÄ0000ÄÄÄÄÁÄÄÄÄ´ ÃÄÄÂÄÄ´ ÃÄÄÂÄÄ´ ÃÄÄÄÄÄo UHF
³ ³ ³ ³ ³
ÄÁÄ ÄÁÄ ÄÁÄ ³ ³
ÄÂÄ C1 ÄÂÄ C2 ÄÂÄ C3 0 L4 0 L5
³ ³ ³ ³ ³
³ ³ ³ ³ ³
oÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄo
GROUND
C1 10pF L1 4 Turns 5MM inside Dia 1 wire space 18 Gauge
C2 18pF L2 As above
C3 18pF L3 As above
- - - - - - - - - - - - - - - -
C4 10pF L4 1 1/2 Turn 3MM inside Dia 1 wire space 18 Gauge
C5 6.8pF L5 As above
C6 10pF
Capacitors disc ceramic or better if you can find them, leadless disc ceramics,
or surface mount (SMD) ceramics. (Don't expect the solder ends to support the
coils, they are not strong enough, use PCB to mount the caps & coils on).
Use good RF practice keep all leads as short as possible.
One option is to make up a box out of PCB material about 2" square by 1" high.
Solder all together to make up an RF tight box. This makes it easy to solder
components to ground. Once constructed solder a lid on.
Connectors can be "N" or "UHF" or BNC.
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ ÃÄÄ¿
³ ³ ³ VHF Port
ÚÄÄ´ ÃÄÄÙ
Aerial ³ ³ Combined Port ³
ÀÄÄ´ ÃÄÄ¿
³ ³ ³ UHF Port
³ ÃÄÄÙ
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
Why Don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
