OpenBCM V1.08-5-g2f4a (Linux)

Packet Radio Mailbox

IZ3LSV

[San Dona' di P. JN]

 Login: GUEST





  
G8MNY  > TECH     02.03.22 11:00l 56 Lines 2443 Bytes #999 (0) @ WW
BID : 61933_GB7CIP
Read: GUEST
Subj: Thermostatic Iron Repair
Path: IZ3LSV<IW8PGT<LU4ECL<GB7CIP
Sent: 220302/0956Z @:GB7CIP.#32.GBR.EURO #:61933 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                 (New Feb 21)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

I pickup a "Weller" type iron by "AdcolA" that has electronic temperature
control, using a negative temperature thermistor with the element. This is
rather than "Magnetic Curie Point" temperature switch of Weller system, or a
thermocouple & sensitive op amp system!

In the handle was a 14 pin control chip which was dud & did not trigger the
triac. So I developed this much simpler 1 transistor circuit as a replacement.

24V oÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
AC   1K                                 ³
2A   _³_                                ³
     \_/                               12R     The thermistor is about 50K cold
      ÃÄÄÂÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿     48W     cold & less than 1K hot. The 3K9
      ³  ³       ³         +    2K   Element   & 150R set lowest & highest temp
      ³ +³      NTC    ÚÄ´ÃÄÄÄÂÄÄ´      ³      with my thermistor.
  10V_³_===    Therm   ³47u ³/  _³_     ³
    '/_\ ³100u   ÃÄÄÄÂÄÁÄÄÄÄ´   \_/=LED ³
      ³  ³      Temp ³ BC337³\e  ³   ___³___
      ³  ³   ÚÄ>pot  ³        ³  ³   _\/_/\_
      ³  ³   ³  2K   ³        ³  ³____/ ³3A
      ³  ³   ÀÄÄÄ´  3K9       ³         ³Triac
      ³  ³      150  ³        ³         ³
0V oÄÄÁÄÄÁÄÄÄÄÄÄÄÁÄÄÄÁÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÙ
                                     iron earth
EÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
                                        ///

The traic is no longer phase fired, as I assume the original IC could do, but a
simple on off including an added status LED (used on some of their irons).

HOW IT WORKS
The 100uF is charged up via 1K & diode to 10V when the zener conducts. The
triac is turned on via the LED & 2K7, giving full power to the heater element.
When the thermistor is hot enough (lower resistance) to put 0.6V on the NPN
base with the preset pot load, the NPN conducts, & bypasses the current going
through the LED & gate, turning the triac off. The 47uF slows the action, so
the triac gets a chance to conduct on both has cycles & even a few on & off, as
shown on the flashing LED.

The circuit needs scoping to check the triac is firing OK on both + & - half
cycles, if not, damage can be done to very small 24V AC transformers!


Also see my Tech Bul on "Soldering Iron Economiser/Boost"


Why Don't U send an interesting bul?

73 De John, G8MNY @ GB7CIP


Read previous mail | Read next mail


 25.12.2024 20:38:34lGo back Go up