|
G8MNY > TECH 27.02.21 13:13l 135 Lines 6293 Bytes #999 (0) @ WW
BID : 25115_GB7CIP
Read: GUEST
Subj: RTT Comms Test Set Use
Path: IZ3LSV<DB0ERF<DB0RES<ON0AR<GB7CIP
Sent: 210227/1110Z @:GB7CIP.#32.GBR.EURO #:25115 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (New Feb 21)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
My now all fully working, modified & calibrated, "Radio Telephony Test Systems"
test set was made in Feltham UK in 1987-9 can be used for quite a lot...
___________________________________________________________
/ /|
/ / |
ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ/ |
Þ /__________________________________________________________/Ý |
Þ³ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿³Ý |
Þ³³ÚÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄ¿ÚÄÄÄÄÄÄÄ¿³³Ý |
Þ³³³ \ AF ³³ \SINAD³³ 5 3 9.9 9 9 9 0 0 ³³ \MOD ³³ \POWER³³³Ý |
Þ³³³__\____³³__\____³³___________________³³__\____³³__\ ___³³³Ý |
ÚÁ³³o _ _ _ _ _ ³³Á¿ |
³_³³ (_)_______(_) (ú) (_) o ø ! ! ! (_) o ³³_³ |
AF³³o _ ³________³ _ _ _ _ .-. ³³ |
in³³o (_) o o (_) (_) ! ! =(_) =(_) (_) o ( o ) ³³RF /
³³CTCSS Lis Vol MOD _ GEN FREQ ú_ú _ _'-'_ ³³in/
³³123ú4 LS 1ú2 (ú) 1 2 3ú4 5 6 7 (ú) (ú) (ú) (ú)³³ /
³ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ³/
~~Þ²Ý~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~Þ²Ý~~
SPECIFICATION
RF Input N socket 50ê 20dB Load atten. 1kW peak, 50W continuous
Power Meter 1-300W, 6 ranges (RF detection for Counter & Rx mode)
Frequency Counter 9 digit 1Hz-540MHz in 3 gate times & 10s averaging to 1Hz
Freq Reference Accuracy < 1/10^7/month, internal Xtal Oven reference
Signal Generator PLL 100Hz steps from 10 - 539.9999MHz, O/P -13dBm (50mV)
Sig Gen Harmonics >-20dBc, Typically >-30dBc
Gen Attenuator 10x1dB & 8x10dB for 1.7uV-50mV via 20dB splitter & 20dB Load
Pilot tone(CTCSS) PLL 20.0Hz-999.9Hz Mod Level adjustable & Rx Counter readout
AF Modulation AF Osc 100Hz-15.9kHz or ext, Level adjustable.
Ext Mod/AF out Needs >1V in, or gives 0-4V RMS AF out, 600ê BNC
Xtal/IF 455kHz & 10.7MHz in built & ext Xtal socket & osc O/P BNC
AF Meter Bal/floating 3mV-10V & dBs 8 ranges, 11Hz-27kHz -3dB
SINAD meter Auto level, 1kHz Notch, 0 to -20dB/100-0% Noise & Distortion
Automatic Rx Scans 2MHz->1GHz, 100mW-300W Load input, up to 60dB S/N
RF & IF O/Ps Rear BNCs for 450-470kHz & RF
Rx AF Filters Comms -3dB 300Hz-3kHz, or HiFi -3dB 50Hz-15kHz
Modulation meter Auto Rx. +/- peak, AM 50/100%, FM 5/100kHz, PM 2/5 Rad
Monitor Amp & LS Vol & 1W for Listening to: AF in, SINAD, AF Osc, & Rx.
Power AC IEC Mains input 230V/115 @ 60W, or XLR for 12V DC @ 5A
Weight 24kg in flight case
Tx MEASUREMENTS
===============
1/ Connecting a Tx to socket of the 300W Dummy Load input you can measure...
ÚÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿ Tx power 0.1-300W 6 power scales.
³PSUÃÄ´ TxÃ>Ä´ Test set³ Frequency 1-540MHz to 1Hz res.
ÀÄÄÄÙ ÀÄÂÄÙ ÀÄÄÄÄÄÄÄÄÄÙ FM Deviation 0-5kHz or 0-100kHz (or AM 0-100%).
Mic CTCSS frequency, CTCSS Modulation deviation.
Hear the modulation on the Test set's LS
2/ Connecting Tx to N socket of the 300W Dummy Load input you can measure....
ÚÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿ With external spectrum analyser
³PSUÃÄ´ TxÃ>Ä´ Test set³ after the 20dB high power atten
ÀÄÄÄÙ ÀÄÂÄÙ ÀÄÂÄÄÄÄÄÄÄÙ & 20dB splitter, but the power
Mic BNC³ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ meter's diode load increases
LinkÀ´Spectrum Analyser³ some of the seen harmonics!
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ Other Tx spuri can be safely seen.
3/ With Rx AF mod BNC patched to AF banana meter input....
ÚÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿
³PSUÃÄ´ TxÃ>Ä´ Test set³ AM/FM Tx Signal Noise >70dB can be measured
ÀÄÄÄÙ ÀÄÂÄÙ ÀÄÄÄÂÄÄÄÄÂÙ via the Comms or Hifi filter.
Mic ÀÄ>ÄÄÙ Hear the Tx noise on Test set's LS.
Rx AF
4/ Mod AF Osc BNC output patched to Mic as well (with a suitable atten/pot).
ÚÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿
³PSUÃÄ´ TxÃ>Ä´ Test set³ AM/FM Tx Distortion can be measured on SINAD meter
ÀÄÄÄÙ ÀÄÂÄÙ ÀÂÄÄÂÄÄÄÄÂÙ & hear the notched distortion on Test set's LS.
MicÀÄÄ<ÄÄÙ ÀÄ>ÄÄÙ AM/FM Tx modulation frequency response 100Hz-15.9kHz.
AFMod Rx AF
1kHz
Rx MEASUREMENTS
===============
5/ Rx patched to Dummy load N, or BNC after stepped atten. for 40dB more.
ÚÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿
³PSUÃÄ´ RxÃ<Ä´ Test set³ AM/FM Rx can tested for freq error & selectivity with
ÀÄÄÄÙ ÀÄÄÄÙ ÀÄÄÄÄÄÄÄÄÄÙ signal gen set to correct or off +/- frequency.
Mod on/off Rx CTCSS recognition & deviation sensitivity checks.
Rx S meter calibration checks.
6/ Rx patched to Dummy load N, & Rx LS to AF input bananas on test set.
ÚÄÄÄ¿ ÚÄÄÄ¿ ÚÄÄÄÄÄÄÄÄÄ¿ AM/FM Rx Frequency response measured.
³PSUÃÄ´ RxÃ<Ä´ Test set³ AM/FM Rx can tested for distortion & sensitivity in
ÀÄÄÄÙ ÀÄÂÄÙ ÀÂÄÄÄÄÄÄÄÄÙ uV signal gen set & modulation applied for 12dB S/N.
LSÀÄÄ>ÄÄÙAF AM/FM max S/Noise (hum etc).
Sinad meter is used for best Rx S/N sensitivity & FM discriminator adjustments.
For that, 5 turns on ferrite ring stops the LS lead being a aerial on weak
signals! RF & DC leads may need the same treatment!
CONCLUSION
==========
All of the above, also permit rig adjustments to improve things.
With SSB kit AM mode have to be used to the Rx only. But SSB Tx 2 tone tests
can be done using CTCSS & beating AF osc from mon LS to the mic & scoping the
RF envolope.
So a useful lab or /P test set. A one stop shop for all rigs, when taken to my
local club's regular test & fixit evenings.
See my tech Buls on "RTT Comms Test Set", Analyser Takeda Riken TR4122B", "AF
Waveform Generator (RS)", "RTT Mod Meter (100)", "FeelTeck Dual DDS Osc FY6600
-60M", "Marconi Distortion Meter TF2337","Marconi 2019A Sig Gen"," Systron
Donner 1702 Sig Gen" "Marconi Counter Type 2432A", "198kHz Off Air Standard",
"Comparing Off Air Freq Standards", "Off Air Lock for Ref Osc", & "Scope RF
Trick".
Why don't U send an interesting bul?
73 de John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |