| |
G8MNY > TECH 26.09.20 11:01l 85 Lines 3174 Bytes #999 (0) @ WW
BID : 7482_GB7CIP
Read: GUEST
Subj: An AF amplifier stage
Path: IZ3LSV<I3XTY<I0OJJ<GB7CIP
Sent: 200926/0841Z @:GB7CIP.#32.GBR.EURO #:7482 [Caterham Surrey GBR] $:7482_GB
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Updated Dec 04)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
This simple amplifier circuit is easy for calculations.
+9V ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄ _
Rc / \
ÚÄÄÄÄÄÄ´ Cout Output Þ Ý
Rb ÃÄÄÄÄ´ÃÄÄÄÄ ³ ³ ³
/'\,/ ³ ³/ Þ Ý Þ
InputÄÄÄ´ÃÄÄÄÁÄÄÄÄ´ NPN \_/
Cin ³\e
³ /'\,/
Re
0VÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄ
BASE BIAS R = Hfe x (Rc+Re) Approx
For « the DC swing on the output. This is because we want the same voltage
CÄE (almost the same as across Rb) as across the total load R of Rc+Re.
GAIN = Rc/Re approx (Rc may be lower due to external load).
With high transisitor current gain Hfe, then Ie approx = Ic, so the
emitter NFB Re controls the collector current making the voltage gain just
the voltage drop ratio of Rc/Re. Assuming no external loads. For high gain
applications Re includes the internal emitter R of the transistor
(typically a few ohms).
Output Z = XCout + (Rc // ((GÄ1) x Rb))
This is the added components, including the apparent fraction of the bias
Rb with load current in it.
"//" means in parallel, many of the paralleled terms are insignificant.
Technically the amount that (G-1)x Rb component that affects the output Z
it will also depend the input source Z.
Input Z = XCin + ((Hfe x Re) // (Rb/(G+1)))
This is the added components, including the apparent fraction of the bias
Rb with input current in it.
"//" means in parallel, many of the paralleled terms are insignificant.
LF Roll off
Cin & Cout affect the LF response. Basically each one will give Ä3dB &
6dB/Octave roll off when Xc equals the source + load Zs.
HF Response
Intrinsically limited by the transistor's FT when the Hfe becomes 1, &
component layout (inter capacitance) causing Miller HF N.F.B. effects
between output & input.
HF Compensation
HF loss can be compensated for by putting a suitable C across Re to give
+3dB boost were Xc=Re, e.g. where the measure drop is -3dB. The 6dB/Octave
lift after that should flatten the amp losses out. The input Z will be
reduced at HF though. Not often used!
EXAMPLE
+12V ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄ
1kê
ÚÄÄÄÄÄÄ´ + Cout
100kê ÃÄÄÄÄ´ÃÄÄÄÄ Output
+ ³ ³/ 0.5uF ³
InputÄÄ´ÃÄÄÄÁÄÄÄÄ´ Hfe=100 10k Load
Cin NPN³\e ³
1uF ³ ³
100ê ³
0V ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
So in the above example Collector should be around +6V
Gain about 9 times
Output Z about 900ê + XCout
Input Z about 5kê + XCin
LF response with input source Z of zero, & output load of 10k...
Input Ä3dB LF roll off, @ 31Hz where Xc = 5kê
Output Ä3dB LF roll off, @ 29Hz where Xc = 10.9kê
Giving Ä6dB @ 30Hz & 12dB/Octave LF cut.
Why don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
