OpenBCM V1.08-5-g2f4a (Linux)

Packet Radio Mailbox

IZ3LSV

[San Dona' di P. JN]

 Login: GUEST





  
G8MNY  > TECH     08.12.19 09:45l 205 Lines 10344 Bytes #999 (0) @ WW
BID : 28677_GB7CIP
Read: GUEST
Subj: Modem Bauds & Bits
Path: IZ3LSV<IK7IJR<IW2OHX<HB9ON<IW8PGT<LU4ECL<GB7CIP
Sent: 191104/0958Z @:GB7CIP.#32.GBR.EURO #:28677 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To  : TECH@WW

By G8MNY                                   (Updated Mar 17)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)

BASEBAND
This is the starting point for data transmission. If the comms channel can
handle DC & have a flat phase & amplitude response in Hz to beyond half the
data rate in bits/S then the link should work. Over very long lines repeaters
may be needed to straighten up the rounded edges & these can be straight
Schmitt triggered amplifier or better still re-clocked (retimed) gated
amplifiers.

  ÚÄÄÄÄÄ¿     Ú      _.Ä¿            ÚÄÄÄÄ¿
  ³  1  ³  0  ³    /' 1  \._0  /     ³  1 ³  0   ³
        ÀÄÄÄÄÄÙ             'ÄÙ           ÀÄÄÄÄÄÄÙ
  GOOD DATA        ROUNDED DATA      TIMING ERRORS

The trouble with the need to find edges in the data to reclock & sync, means
either a clock must be included with the data, or the data must have enough
alternations (0 & 1s) that the clock can always be extracted.

When no DC path is available then all is not lost if the data is short & has no
substantial DC component, then a DC clamp & restore circuit will work, as will
random encrypted data system (spread spectrum) that has no net DC.

Anything else needs a Modulator & Demodulator "Modem" to translate the baseband
to higher frequencies suitable to telephone line or radio path.

VSB (AM)
It is possible to send the data as Vestigial Side Band (part of AM signal),
utilising nearly all the available spectrum to carry an information sideband.
With VSB a carrier is sent near to the edge of the passband, this ensures the
DC component is sent OK.

          Channel Width        Only a tiny fraction of the LSB is sent enough
 ³  |.-~³~-._            |     to make the carrier in the linear phase & level
 ³  |   ³    ~-._        |     part of the channel bandwidth. This gives the
 ³  |LSB³  USB   ~-._    |     maximum Baud rate possible for any channel.
 ³  |   ³            ~-._|     BAUD is the changes per second, & DATA RATE is
 ÅÄÄÂÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÂÄ    the number of bits per second.
  300  400             2700Hz  In single level AM, AFSK or FSK there is a 1:1
         <-baseband data->     relationship, 1 bit/s = 1 baud.

In this example 2300 Hz of baseband band data gives 4600 baud or bits/s on a
narrow SSB channel.

However there are loads of problems with AM & VSB modes for data, so FM with
its 2 sidebands became the dominant mode...

FSK 1200B/S
                                  This is fairly typical of what happens as
             0         1          the FM idle carrier at 1800Hz causes 2 AM CW
 ³    600Hz /³\       /³\ 600Hz   signals to appear at the deviation limit
 ³     of  / ³ \     / ³ \  of    points representing the data 0 & 1.
 ³    LSB /  ³  \   /  ³  \ USB   Each of these carries has a full double AM
 ³       /   ³   \ /   ³   \      sidebands up to the baud rate/2 in Hz, as it
 ÅÄÄÄÄÄÄÁÄÄÄÄÁÄÄÄÄÄÄÄÄÄÁÄÄÄÄÁÄ    needs 2 bits to form a cycle.
 0 300 600  1k2  1k8  2k4   3k    (1800Hz carrier is used as it is the fastest)
                                  (frequency on most telephone lines.)

In this example the data rate would be locked to the carrier frequency, if not
locked system then similar but not exactly the same modem frequencies are used.

For this FSK to work, a bandwidth of 600Hz - 3kHz is needed, it does not have
to be too level flat, as FM can be hard limited, & that removes level changes
as well as almost all noise effects.

So a bad line/comms link with more than 15dB frequency spread & worse than 15dB
S/N is still error free despite being very poor for phone use.

However differing delay times for the 2 tones is critical, & a Group Delay
difference of less that 1mS between 1200Hz & 2400Hz will garble the data, as
the modem will Rx no tone, then 2 tones etc. This has no affect on comms phone
audio!

Typical Group Delay of a long loaded line, or via a comms Rx IF filter!
   Delay
 1200uS´ \ Transformers              / Channel
  900uS´  \  & caps                 /  Low pass
  600uS´   ~-_                     /   Filtering
  300uS´      ~~ÄÄ..__         _.Ä~
    0uS´              ~~ÄÄ---Ä~
       ÅÄÂÄÄÂÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÂÄÄÄÂÄÄÂÄÄÂÄÄ>Frequency
       300 500 800  1k2  1k6  2k   2k4 2k7 3k 3k2 3k4 Hz

Sent data                                Rx Data with 833uS of group delay!

______~~~~~~____________~~~~~~~~~~~~    ______????????????______??????~~~~~~
  0     1     0     0     1     1         0     no   0+1     1    no     1
1200  2400  1200  1200  2400  2400      1200   Sig 1k2+2k4       Sig   2400

Even so this is one of the simplest & robust standards around (this why it is
still used), however it is important to have all the sidebands that make up the
signal turning up all at the same time & at simular levels & also not
completely drowned out in noise or over distorted.

GOING FASTER
If we look at what a telecomms line can pass e.g. 300Hz - 3.3kHz with some
frequency attenuation & group delay. Then that would support a max baud rate
of 3000 baud, e.g. an 1800Hz carrier with double sidebands up to ñ1500Hz.

 ³   1500Hz /³\ 1500Hz                Alternating baud signals of
 ³   of   /  ³  \ of                  010101 @ 3000 baud forms the
 ³   LSB/    ³    \USB                highest side bands of ñ1500Hz.
 ³    /      ³      \
 ÅÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÁÄÄÄ> Frequency
 0  300     1k8      3k3   Hz

However this is not the data rate,           ÚÄÄÄÄÂÄÄÄÄ¿
but the max baud rate. Using Phase           ³ 00 ³ 01 ³
Modulation PM on 4 phases (Quadriture        ÃÄÄÄÄÅÄÄÄÄ´
Phase Shift Keying) you get 1 of 4           ³ 10 ³ 11 ³
states per baud or 2 bits per Baud (Dibits)  ÀÄÄÄÄÁÄÄÄÄÙ

But by using AM multiple levels as well as PM together, it is possible to make
a "single baud of carrier" represent 1 of many states, e.g. 16 AM levels & 16
phase angles, gives 256 (256QAM) states or symbols, which is equal to 8 bits
of data per baud! That would make a data rate of 8x3k = 24kB/S.

Phase & level diagram (dartboard vector) for just 4x 4 (16 symbols, 16QAM)

   +4´ [0]                     [1]
   +3´    [4]               [5]    This give 16 pigeon holes (0-F) for each
   +2´       [8]         [9]       burst of carrier signal (baud) to drop into.
   +1´          [C]   [D]
    0´              0              In practice the 4 phase are rotated per
   -1´          [F]   [E]          level shell to give the bigger pigeon
   -2´       [B]         [A]       holes.
   -3´    [7]               [6]
   -4´ [3]                     [2] Note that the carrier level of 0 can't be
     ÀÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄ uses as it would not give any phase info.
 LEVELS-4 -3 -2 -1  0 +1 +2 +3 +4


   +4´ [ ][ ][ ][ ]   [ ][ ][ ][ ]
   +3´ [ ][ ][ ][ ]   [ ][ ][ ][ ]   By using variable number of phases per
   +2´ [ ][ ][ ][ ]   [ ][ ][ ][ ]   carrier level, you can fill all the
   +1´ [ ][ ][ ][ ]   [ ][ ][ ][ ]   pigeon holes as close as possible, giving
    0´              0                the biggest number of symbols, here 6 bits
   -1´ [ ][ ][ ][ ]   [ ][ ][ ][ ]   per baud gives 64QAM.
   -2´ [ ][ ][ ][ ]   [ ][ ][ ][ ]
   -3´ [ ][ ][ ][ ]   [ ][ ][ ][ ]   Noise, distortion, poor frequency/phase
   -4´ [ ][ ][ ][ ]   [ ][ ][ ][ ]   response will move the carrier into the
     ÀÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄÄÂÄ   wrong pigeon hole, & produce 6 errors
 LEVELS-4 -3 -2 -1  0 +1 +2 +3 +4    at once!

However you don't get something for nothing, using 16 levels means the
distortion & all noise must put the level into the next 6.25% level window, or
3.1% (-31dB peak). And the same goes for multiple phase mod, due to jitter &
multipath etc. that must not to exceed 1/32 of a cycle peak @ 1800Hz! A very
tight specification for radio path!

EQUALISING (training)
As the line will not be flat or have no group delay it is important that the
modem has an equaliser that has the opposite characteristics to the line. This
used to be an analogue nightmare, but with digital A-D convertion of the line
audio signal, it is relatively simple to flatten in software!

e.g. a Line with bump at 1kHz
Level                          Add in a % of signal data from 500mS ago & the
  ³            /~\             bump will go. But then you get a bump @ 2kHz,
  ³     .-----~   ~----.       so add in some signal data from 250mS ago, keep
  ³    /                \      doing this until all bumps are above 3.4kHz.
  ÅÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄÄÄÂÄÄ
  0  250  500  1k   2k    4kHz

Training can also be done on live data, by making small adjustments & seeing if
the data quality (how near Rx symbols are to their pigeon hole's ideal centres)

Ideal Symbol   Amplitude     Phase         Noise &        a Symbol
in Centre of    Trouble     Trouble      Distortion       in Error
  ÚÄÄÄÄÄÄÄ¿        ±±                       ±±±±±        ÚÄÄÄÄÄÄÄ¿
  ³       ³        ±±                      ±±±±±±±       ³       ³ O
  ³   O   ³        ±±      ±±±±±±±±±       ±±±±±±±       ³       ³
  ³       ³        ±±                       ±±±±±        ³       ³
  ÀÄÄÄÄÄÄÄÙ        ±±                                    ÀÄÄÄÄÄÄÄÙ
 Pigeon Hole    up/down    Sideways 
              from centre  ref centre

So you see that although modern modems are super at equalising & giving 56kB/S
max on a good short line, they can only do that over clean copper circuits, &
high quality PCM audio systems that give <1% THD >50dB S\N & no phase jitter!

In practice most lines can't do this, so the modem is designed to drop back the
baud (symbol rate) & or the number of levels/phase angles (symbols). Also the
modem has error detection/correction, so missed errors that are passed through
are low. The use of an encryption algorithm in some modems also minimises
continuous retries of data patterns that might have high error rates.

BROADBAND
These systems are different & use much wider frequency range & multiple
carriers each carrying some of the data in QPSK. But there are similarities, &
nasty line problems will greatly reduce the usable data rate. A common cause of
broadband data rate changing/hiccups is the need for the modem to re-establish
what frequencies can be use due to changing QRM, e.g. Nightime AM station, or
an old analogue cordless phone occasionally in use sending signals on the same
cable as your broadband.


Why Don't U send an interesting bul?

73 de John G8MNY @ GB7CIP


Read previous mail | Read next mail


 24.12.2024 18:23:57lGo back Go up