| |
G8MNY > TECH 12.03.19 11:28l 95 Lines 4227 Bytes #999 (0) @ WW
BID : 62100_GB7CIP
Read: GUEST
Subj: Unijunction Transistor Circuit
Path: IZ3LSV<IK6ZDE<IW0QNL<JH4XSY<N3HYM<GB7CIP
Sent: 190312/1028Z @:GB7CIP.#32.GBR.EURO #:62100 [Caterham Surrey GBR]
From: G8MNY@GB7CIP.#32.GBR.EURO
To : TECH@WW
By G8MNY (Correction Apr 18)
(8 Bit ASCII graphics use code page 437 or 850, Terminal Font)
Unijunction transistors are strange animals, not often found they have 2 bases
that are on the same bar of silicon with an emitter in the middle. They exhibit
a -ve impedance characteristic emitter to base 1 & as such easily form simple
oscillators. But as they are slow devices they are not useful for radio work.
TIMEBASE
Here is an example of a Unijunction transistor used for a simple timebase from
5 sec period to 20 Hz, for higher speeds change C1 for 0.1uF or 10nF.
+12V ÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
56k ³ / Tag
³ 100ê _n_
2M N ³ b2/. .\e
VARIABLE UJT b2 ³ 2N ³ . ³
³______ ÃÄÄÄÙ 2646 \___/b1
³ \->³
1u === e ÃÄÄÄÄÂÄÄÄ> Pulse O/P Base View
C1 ³ b1 ³
³ 470ê
0V ÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄ
HOW IT WORKS
When C1 charges up to the trigger voltage of the UJT, it fires & discharges the
C1 producing a voltage spike on the Base 1. The 100ê is for protection of the
load & UJT.
PRACTICAL MAINS LIVE STROBE CIRCUIT
+340V
ÚÄÄ250êÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
_³_ 10W ³ |o| 4 Jules, 50 Watt
/_\ === 8uF 800v | | Strobe tube
Fuse oÄÄÄ´ ³ "Nitrogel" | |ÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
1A | ³ ³ Pulse Cap |o| ³
L-o \Äo ³ -340VÃÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ ³
³ ³ ³
N-o \ÄÄÄÄÄ)ÄÄÄÄÄÂÄÄ)ÄÄÄÂÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿ ³
On/Off ³ ³ ³ 68k 1W 68k ³
³ ³ ³ ÃÄÄÄÂÄÄÄÄÄÄÄÄ100êÄÄ¿ 1W 250V ³
_³_ ³ ³ ³ 2M Pot ³ ³ u1 ³
1N /_\ +³ ³ ³ Variable N ³ ÃÄÄÄÂÄ´ÃÄ¿ ³
4007 ³ === ³ ³ ³ UJT ³ SCR_³_ ³ ³ ³
³ 100u³ ³ ³ ÀÄ56kÄÄÄ¿_ ÃÄÙ 2N _\_/_ ³ )|( 5kV
³ 350V³ ³ _³_ ³ \->³ 2646 /³ ³ )|( Pulse
250ê ³ ³ /_\' 1u ³ ÃÄÂÄÄÄÄÄÄÂÙ ³ 100k )|( 25:1
10W ³ ³ ³18V === ³ 470ê ³ ³ )|( Transformer
³ ³ ³ ³ ³ 470ê ³ ³ ³ ³ ³
ÀÄÄÄÄÄÁÄÄÁÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÄÄÄÄÁÄÄÁÄÄÄÁÄÄÄÄÁÄÄÄÙ
-340V
This strobe circuit uses the UJT pulse circuit to trigger a small SCR that
discharges a 250V u1 cap into an pulse ignition transformer (small highly
insulated coil). The AC pulse of the 0.1uF & Transformer, the brief gate
trigger pulse & the low current through the 68k insure the SCR can't remain on
between pulses. The 100k limits the trigger circuit voltage to 200V.
This stepped up high AC voltage spike applied to the outer trigger electrode
starts up a discharge in the 50W strobe tube that discharges the special pulse
capacitor that was charged up to 680V DC.
The whole circuit is mains live & housed in a well earthed metal box with
plastic shafted pot & main switch frame mounted off the case.
The large coiled strobe tube is at the prime focus of a reflector (car
headlight sized reflector). Smaller power tubes can be used just change the 8uF
for a smaller value to suit the tube flash & continuous power ratings.
2 2
Strobe Energy = «CVs - «CVd , Where Vs = start volts, & Vd = discharged Volts.
2 2
But as Vs is much larger than Vd , the Vd component can be ignored.
« x 8 x 10(^-6) x 680 x 680 = 1.85 Watts/Pulse (Jules)
But @ 20 Pulses per second that is 37 Watts! Hence the 50W rating of the tube.
The common photographic flash gun tubes, are over run at 100x brighter than
strobe tubes & last only a few thousand flashes as they suffer immense thermal
shock at each flash.
Strobe tube flashes for several tens of million of flashes!
Why don't U send an interesting bul?
73 De John, G8MNY @ GB7CIP
Read previous mail | Read next mail
| |
